|
| 貨號 | PARATHERMT™ HR SYNTHETIC- AROMATIC HTF |
| 品牌 | PARATHERMT™ HR SYNTHETIC- AROMATIC HTF |
| 是否危險化學品 | 否 |
| 型號 | PARATHERMT™ HR SYNTHETIC- AROMATIC HTF |
| 產品等級 | 其他 |
| 包裝規格 | 桶 |
| CAS編號 | |
| 純度 | 98% |
| 別名 | PARATHERMT™ HR SYNTHETIC- AROMATIC HTF |
| 密度 | 1.3g/cm3 |
| 產地/廠商 |
HR synthetic-aromatic heat transfer fluid is an alkylated-aromatic based heat transfer fluid formulated for closed-loop liquid phase heating to 650°F in fired heaters and 675°F in waste heat recovery and full convection heaters. HR synthetic-aromatic thermal fluid offers greater thermal stability than competitive aromatic based fluids that cover similar temperature ranges. Testing (ASTM D6743) shows that, compared to its closest competitor, HR synthetic-aromatic heat transfer fluid experiences 1/2 the amount of fluid degradation when maintained at 700°F for 500 hours. Less degradation means less maintenance and a longer fluid life. Centrifugal pumps are generally specified around the fluid viscosity at the desired operating temperature (usually less than 2 cps). Capacity falls off significantly above 300 cps. So the actual minimum start-up temperature of a fluid is where the viscosity curve crosses the 300 cps line. HR Synthetic-Aromatic Heat Transfer Fluid’s lower cold start-up temperature of 13°F (-11°C) offers a significant advantage over other high-temperature fluids.
| Minimum Startup Temp (300cSt) | Maximum Operating Temp |
|---|---|
| 11°F / -12°C | 675°F / 357°C |
Note: If you are experiencing short supply, or long lead times for your currently specified synthetic/aromatic 650°F (terphenyl or alkylated aromatic) heat transfer fluid, call Paratherm for a point-by-point comparison of physical properties. We have product available, and may have just the fluid for your application. +1 (610) 860-6323. Or, use the links on the left side of this page to compare properties with Therminol 66.
| Property | Paratherm HR | Therminol 66 |
|---|---|---|
| Chemical Composition | Alkylated Aromatic | Modified Terphenyl |
| Maximum Operating Temperature | 650°F (343oC) | 650°F (343°C) |
| Maximum Film Temperature | 700°F (371 C) | 705°F (374°C) |
| Minimum Start-up Temp (300 cSt) | 11.0°F (-12°C) | 52.0°F (11°C) |
| Kinematic Viscosity @ 40 C | 11.0 cSt | 29.6 cSt |
| Kinematic Viscosity @ 100 C | 2.4 cSt | 3.8 cSt |
| Density @ 25 C | 7.98 lb/gal (956 kg/m3) | 8.39 lb/gal (1005 kg/m3) |
| **Degree of Decomposition (ASTM D6743) | 0.15 | 0.56 |
*Therminol 66 is a trademark of Solutia Inc.
**The Degree of Decomposition, measured through ASTM D6743, reflects the overall thermal degradation of a thermally stressed fluid at a specific test temperature. It is determined by adding the total mass percentage of all decomposed products found in a thermally stressed sample. These values were found after both fluids were tested side-by-side at 370oC (698oF) for 500 continuous hours. A lower Degree of Decomposition reflects superior relative Thermal Stability of a fluid.
